S 2115 Safety system with current limitaion, HV current < 3 mA
Accessories
S 2115 Standard set
- S 2115/1 Safety system with current limitaion, HV current < 3 mA
- S 2115/2 Current limiter
- A 1728 Mains cable C13 / Schuko, 3 x 0.75 mm2, 2 m
- A 1773 Crocodile clip, red, (HV)
- A 1602 HV test lead with test probe, blue, 1.5 m
- A 1690 Start button
- A 1689 Emergency stop button
- A 1017 Communication cable, RS232, 2 m
In many countries additional workplace safety measures are not needed during the high voltage testing with a.c. up to 3mA. If the current is higher than 3 mA a special test system with automatic protection against direct contact or a sealed off area with warning light and two-handed operation is required. This Safety module is intended for limitation of the test current in the HV tests to a safe level. It consists of two boxes. The first box S 2115_1 contains resistors that are connected in series with the HV measuring circuit. The resistors significantly reduce the output power of the high voltage circuit (short circuit power < 20 mA). The second box S 2115_2 contains a current monitor. If the test current exceeds 3 mA the inbuilt current monitor will disconnect the measuring circuits from the mains within a safe time. The START button is intended to activate the safety module after being (re-)energized.
Do you own this product?
Standards applied
Electrical switchboards safety
- ESB Competences: Electrical Switchboards Safety Testing
- IEC/EN 61439-1 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
Machine safety
- MST Competences: Machines Electrical Safety Testing
- IEC/EN 50191 Erection and operation of electrical test equipment
- IEC/EN 60950 Information technology equipment – Safety
Portable appliances safety
- PAT Competences: Portable Appliances Safety Testing
- IEC/EN 60335-1 Household and similar electrical appliances - Safety
- IEC/EN 60598-1 Luminaires - Part 1: General requirements and tests
- VDE 0701 Inspection after repair, modification of electrical appliances - periodic
- VDE 0702 Inspection on electrical appliances - general requirements for electrical safety
Instrument safety towards user
- Directive EMC 89/336/EE on electromagnetic compatibility
- IEC/EN 61010-031 Amendment 1 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held and hand-manipulated probe assemblies for electrical test and measurement
Properties
Key features
- The highest protection grades up to PLe or SIL3 can be achieved;
- Protection against direct contact;
- All components in the safety modules are approved safety devices;
- Simple integration into the measuring system.
Optional accessories
A 1494 2M HV test pistol with 2 m cable, blue
High voltage safety test probe for manual high voltage testing. The test tip is protected by an arc-resistant teflon tube, and it has built in almost wear-free lungsten which assures a long lifetime.
A 1494 15M HV test pistol with 15 m cable, blue
High voltage safety test probe for manual high voltage testing. The test tip is protected by an arc-resistant teflon tube, and it has built in almost wear-free lungsten which assures a long lifetime.
Downloads
| Datasheet | Language | Version | Release | Notes | Type | Size | Download |
|---|---|---|---|---|---|---|---|
| S 2115 Safety system with current limitaion, HV current < 3 mA | en | 2021 | 24.02.2021 | 522.99 KB |
|
| Manual | Language | Version | Release | Notes | Type | Size | Download |
|---|---|---|---|---|---|---|---|
| S 2109 / S 2110 / S 2111 / S 2115 Safety system | en | 1.1.1 | 24.02.2021 | 20 753 023 | 2.01 MB |
Login
|
Where to buy?
Search for distributors and partners
Have a question?
Speak with a specialist
